Article Article
Assessment of Composite Aluminum Adhesive Joints Using Digital Image Correlation

Traditional nondestructive evaluation (NDE) methods present significant challenges to detecting and characterizing kissing or weak bonds in adhesively bonded structures. These kissing or weak bonds also cannot transmit shear stresses or handle complex loading modes and, if not detected, can present a significant threat to the structural integrity of the components or systems. This paper demonstrates the digital image correlation (DIC) technique for evaluating adhesively bonded dissimilar materials joints subjected to kissing or weak bonds. The study employed four adhesively bonded carbon fiber reinforced plastics and aluminum (CFRP-Al) lap-shear test coupons with varied bond quality (i.e., with no contamination and three simulated kissing bond defects). The novelty of the approach presented in this paper was that this technique could detect and demonstrate changes in the normal strain (εyy) contour map of the contaminated specimens at relatively lower load levels. This load level corresponds to 15% of the failure load for the silicone and hydraulic oil contaminated sample and around 30% for the polyvinyl alcohol (PVA) contaminated sample. In addition, higher compressive strains along the overlap edges were observed in the strain map for the single lap joints due to the higher peeling stresses of the adherend and the stress concentration at the edges of an adhesively bonded joint.



Adams, D.E., N.D. Sharp, N. Myrent, and R. Sterkenburg. 2011. “Inspection for kissing bonds in composite materials using vibration measurements.” Proc. SPIE 7983, Nondestructive Characterization for Composite Materials, Aerospace Engineering, Civil Infrastructure, and Homeland Security 2011, 79830W (18 April 2011);

Adams, R. D., P. Cawley, and C.C.H. Guyott. 1987. “Nondestructive Inspection of Adhesively Bonded Joints.” Journal of Adhesion 21 (3–4): 279–90.

ASTM. 1995. ASTM D2651-90: Standard Guide for Preparation of Metal Surfaces for Adhesive Bonding. ASTM International. West Conshohocken, PA.

ASTM. 2014. ASTM D5868-01: Standard Test Method for Lap Shear Adhesion for Fiber Reinforced Plastic (FRP) Bonding. ASTM International. West Conshohocken, PA.

Bockenheimer, C., D. Fata, W. Possart, M. Rothenfusser, U. Netzelmann, and H. Schaefer. 2002. “The Method of Non-linear Ultrasound as a Tool for the Nondestructive Inspection of Structural Epoxy-Metal Bonds - a resume.” International Journal of Adhesion and Adhesives 22 (3): 227–33.

Bossi, R., K. Housen, and W. Shepherd. 2002. “Using Shock Loads to Measure Bonded Joint Strength.” Materials Evaluation 60 (11): 1333–38.

Bossi, R., K. Housen, C. T. Walters, and D. Sokol. 2009. “Laser Bond Testing.” Materials Evaluation 67 (7): 819–27.

Brotherhood, C.J., B.W. Drinkwater, and S. Dixon. 2003. “The Detectability of Kissing Bonds in Adhesive Joints Using Ultrasonic Techniques.” Ultrasonics 41 (7): 521–29.

Brotherhood, C.J., B.W. Drinkwater, and F.J. Guild. 2002. “The Effect of Compressive Loading on The Ultrasonic Detectability of Kissing Bonds in Adhesive Joints.” Journal of Nondestructive Evaluation 21 (3): 95–104.

Cerniglia, D., N. Montinaro, and V. Nigrelli. 2008. “Detection of Disbonds in Multi-layer Structures by Laser-Based Ultrasonic Technique.” Journal of Adhesion 84 (10): 811–29.

Chambers, J. K., and J. R. Tucker. 1999. “Bondline Analysis Using Swept-Frequency Ultrasonic Spectroscopy.” Insight (American Society of Ophthalmic Registered Nurses) 41 (3): 151–55.

Chu, T. C., W. F. Ranson, and M. A. Sutton, 1985. “Applications of Digital Image Correlation Techniques to Experimental Mechanics.” Experimental Mechanics 25 (3): 232–44.

Colavito, K.W., J. Gorman, E. Madenci, and S.S. Smeltzer III. 2009. “Refinements in Digital Image Correlation Technique to Extract Adhesive Strains in Lap joints,” 50th AIAA/ASME/ASCE/AHS/ASC Structures, Structural Dynamics, and Materials. American Institute of Aeronautics and Astronautics.

Crocombe, A. D., C. Y. Ong, C. M. Chan, M. M. A. Wahab, and I. A. Ashcroft. 2002. “Investigating Fatigue Damage Evolution in Adhesively Bonded Structures Using Backface Strain Measurement.” Journal of Adhesion 78 (9): 745–76.

Ehrhart, B., b. Valeske, C.-E. Muller, and C. Bockenheimer. 2010. “Methods for the Quality Assessment of Adhesive Bonded CFRP Structures - A Resume,” Proc. 2nd Intl. Symposium on NDT in Aerospace 2010 – We.5.B.2.

Graner Solana, A., A. D. Crocombe, and I. A. Ashcroft. 2010. “Fatigue Life and Backface Strain Predictions in Adhesively Bonded Joints.” International Journal of Adhesion and Adhesives 30 (1): 36–42.

Guo, G., J. Tu, Y. Zhang, and Y. Shi. 2012. “Inspection of Kissing-Bond Defect in Honeycomb Structure by Shearography,” Proc. 18th World Conference on Nondestructive Testing.

Guyott, C. C. H., P. Cawley, and R. D. Adams. 1986. “The Nondestructive Testing of Adhesively Bonded Structure- A Review.” Journal of Adhesion 20 (2): 129–59.

Heslehurst, R. B. 1999. “Observations in the structural response of adhesive bondline defects.” International Journal of Adhesion and Adhesives 19 (2-3): 133–54.

Hirsekorn, S. 2001. “Nonlinear Transfer of Ultrasound by Adhesive Joints - A Theoretical Description.” Ultrasonics 39 (1): 57–68.

Jeenjitkaew, C., Z. Luklinska, and F. Guild. 2010. “Morphology and Surface Chemistry of Kissing Bonds in Adhesive Joints Produced by Surface Contamination.” International Journal of Adhesion and Adhesives 30 (7): 643–53.

Kundu, T., A. Maji, T. Ghosh, and K. Maslov. 1998. “Detection of Kissing Bonds by Lamb Waves.” Ultrasonics 35 (8): 573–80.

Lilleheden, L. 1994. “Mechanical Properties of Adhesives in situ and in bulk.” International Journal of Adhesion and Adhesives 14 (1): 31–37.

Marty, P. N., Desai, N., and Anderson, J., 2004, “NDT of Kissing Bond in Aeronautical Structures,” Proc. 16th WCNDT 2004, Montreal, Canada.

Michaloudaki, M., E. Lehmann, and D. Kosteas. 2005. “Neutron Imaging as a Tool for the Non-destructive Evaluation of Adhesive Joints in Aluminium.” International Journal of Adhesion and Adhesives 25 (3): 257–67.

Moreira, D. C., and L. C. S. Nunes. 2014. “Experimental analysis of bonded single lap joint with flexible adhesive.” Applied Adhesion Science 2 (1): 1–8.

Moutrille, M.-P., K. Derrien, D. Baptiste, X. Balandraud, and M. Grédiac. 2009. “Through-thickness strain field measurement in a composite/aluminium adhesive joint.” Composites Part A: Applied Science and 

Manufacturing, 40 (8): 985-996.

Nagy, P. B. 1991. “Ultrasonic Detection of Kissing bonds at Adhesive Interfaces.” Journal of Adhesion Science and Technology 5 (8): 619–30.

Pocius, A. V., D. A. Dillard, and M. K. Chaudhury. 2002. Adhesion Science and Engineering-I. Amsterdam, The Netherlands: Elsevier.

Ruiz, P. D., F. Jumbo, J. M. Huntley, I. A. Ashcroft, and G. M. Swallowe. 2011. “Experimental and Numerical Investigation of Strain Distributions Within the Adhesive Layer in Bonded Joints.” Strain 47 (1): 88–104.

Ruiz, P. D., F. Jumbo, A. Seaton, J. M. Huntley, I. A. Ashcroft, and G. M. Swallowe. 2006. “Numerical and Experimental Investigation of Three-Dimensional Strains in Adhesively Bonded Joints.” Journal of Strain Analysis for Engineering Design 41 (8): 583–96.

Tsai, M. Y., and J. Morton. 1995a. “An Experimental Investigation of Nonlinear Deformations in Single-Lap Joints.” Mechanics of Materials 20 (3): 183–94.

Tsai, M. Y., and J. Morton. 1995b. “The Effect of a Spew Fillet on Adhesive Stress Distributions in Laminated Composite Single-Lap Joints.” Composite Structures 32 (1-4): 123–31.

Tsoi, K. A., and N. Rajic, 2011, “Non-destructive Evaluation of Aircraft Structural Components and Composite Materials at DSTO Using Sonic Thermography,” Air Vehicles Division, Defence Science and Technology Organisation, DSTO-TN-0986, Victoria, Australia.

Vijaya Kumar, R. L., M. R. Bhat, and C. R. L. Murthy. 2013a. “Evaluation of Kissing Bond in Composite Adhesive Lap Joints Using Digital Image Correlation: Preliminary Studies.” International Journal of Adhesion and Adhesives 42:60–68.

Vijaya Kumar, R. L., M. R. Bhat, and C. R. L. Murthy. 2013b. “Experimental Analysis of Composite Single-Lap Joints Using Digital Image Correlation and Comparison With Theoretical Models.” Journal of Reinforced Plastics and Composites 32 (23): 1858–76.

Vinson, J. R. 1989. “Adhesive Bonding of Polymer Composites.” Polymer Engineering and Science 29 (19): 1325–31.

Waugh, R. C., J. M. Dulieu-Barton, and S. Quinn. 2011. “Pulse Phase Thermography and its Application to Kissing Defects in Adhesively Bonded Joints.” Applied Mechanics and Materials 70:369–74.

Yan, D., B. W. Drinkwater, and S. A. Neild. 2009. “Measurement of the Ultrasonic Nonlinearity of Kissing Bonds in Adhesive Joints.” NDT & E International 42 (5): 459–66.

Yan, D., Y., B.W. Drinkwater, and S.A. Neild. 2010. “Experimental and Theoretical Characterization of in Adhesive Joint Using Non-Linear Ultrasonic Measurement.” AIP Conference Proceedings 1211:1190–97.

Yan, D., Y., S. A. Neild, and B. W. Drinkwater. 2012. “Modelling and Measurement of the Nonlinear Behaviour of Kissing Bonds in Adhesive Joints.” NDT & E International 47:18–25.


Usage Shares
Total Views
140 Page Views
Total Shares
0 Tweets
0 PDF Downloads
0 Facebook Shares
Total Usage