Article Article
A Multiple-Echo Calibration Technique for Guided Wave Testing

Guided wave testing has become an established technology for screening long lengths of pipe for safety-critical defects from a single transducer position. The location of any defect is accurately determined and a rough idea of defect severity is obtained. However, it would be very beneficial to obtain a more accurate severity estimate from the guided wave data, especially in cases where follow-up inspection is expensive. This requires a more reliable calibration technique than the conventional approach, which relies on assumptions about the amplitudes of weld reflections. A multiple-echo calibration technique using data collected with standard test protocols but processed to extract the amplitude of reverberations between two features on either side of the sensor ring is presented, which removes the need for assumptions about the weld reflection amplitudes that reduce the accuracy of the conventional method of calibration. This novel technique is less dependent on operator judgement, and field examples presented show that it gives more accurate measures of cross-section loss than the conventional calibration technique. The improvement is particularly marked in cases where the weld geometry is not known or is nonuniform.

DOI: https://doi.org/10.32548/2022.me-04255

References

Alleyne, D.N., B. Pavlakovic, M.J.S. Lowe, and P. Cawley, 2001, “‘Rapid, Long Range Inspection of Chemical Plant Pipework Using Guided Waves,” Insight, Vol. 43, pp. 93–96, 101

ASTM, 2011, ASTM E2775-11: Standard Practice for Guided Wave Testing of Above Ground Steel Pipework Using Piezoelectric Effect Transduction, ASTM International, https://doi.org/10.1520/E2775-11

Birch, S., and F. Baker, 2007, “Long-Range Guided-Wave Ultrasonics: A New Age in Pipeline Inspection,” Inspection Trends, Vol. 10, pp. 13–17

BSI, 2011, BS 9690(1–2): Non Destructive Testing - Guided Wave Testing, BSI Group – British Standards, UK

Carandente, R., and P. Cawley, 2012, “The Effect of Complex Defect Profiles on the Reflection of the Fundamental Torsional Mode in Pipes,” NDT & E International, Vol. 46, pp. 41–47, https://doi.org/10.1016/j.ndteint.2011.11.003

Cawley, P., M.J.S. Lowe, D.N. Alleyne, B. Pavlakovic, and P. Wilcox, 2003, “Practical Long Range Guided Wave Testing: Applications to Pipes and Rails,” Materials Evaluation, Vol. 61, pp. 66–74

Demma, A., P. Cawley, and M. Lowe, 2003, “The Reflection of the Fundamental Torsional Mode from Cracks and Notches in Pipes,” The Journal of the Acoustical Society of America, Vol. 114, https://doi.org/10.1121/1.1582439

Demma, A., P. Cawley, M. Lowe, A.G. Roosenbrand, and B. Pavlakovic, 2004, “The Reflection of Guided Waves from Notches in Pipes: A Guide for Interpreting Corrosion Measurements,” NDT & E International, Vol. 37, pp. 167–180, https://doi.org/10.1016/j.ndteint.2003.09.004

Demma, A., P. Cawley, M. Lowe, and B. Pavlakovic, 2005, “The Effect of Bends on the Propagation of Guided Waves in Pipes,” Journal of Pressure Vessel Technology, Vol. 127, pp. 328–335, https://doi.org/10.1115/1.1990211

Heinlein, S., P. Cawley, and T.K. Vogt, 2018, “Reflection of Torsional T(0,1) Guided Waves from Defects in Pipe Bends,” NDT & E International, Vol. 93, pp. 57–63, https://doi.org/10.1016/j.ndteint.2017.09.007

Holmes, C., B.W. Drinkwater, and P.D. Wilcox, 2005, “Post-Processing of the Full Matrix of Ultrasonic Transmit–Receive Array Data for Non-destructive Evaluation,” NDT & E International, Vol. 38, pp. 701–711, https://doi.org/10.1016/j.ndteint.2005.04.002

JIS, 2010, JIS NDIS 2427: General Principles of Guided Wave Inspection for Piping by Pulse Echo Technique (in Japanese), Japanese Industrial Standards, Japan

Kim, S.Y., H. Kwun, and G.M. Light, 2005, “Improving Guided Wave Testing of Pipelines with Mechanical Attachments,” Materials Evaluation, Vol. 68, pp. 927-932

Mudge, P.J., 2001, “Field Application of the Teletest Long Range Ultrasonic Testing Technique,” Insight, Vol. 43, pp. 74–77

NACE, 2013, SP0313-2013-SG: Guided Wave Technology for Piping Applications, National Association of Corrosion Engineers International, Houston, TX

Nuñez Ledesma, V.M., E. Pérez Baruch, A. Demma, and M.J.S. Lowe, 2009, “Guided Wave Testing of an Immersed Gas Pipeline,” Materials Evaluation, Vol. 67, pp. 102–115

Vogt, T., 2010, US Patent 20130179098A1, Processing Signals Acquired During Guided Wave Testing, filed 28 July 2010, and issued 27 March 2018

 

Metrics
Usage Shares
Total Views
133 Page Views
Total Shares
0 Tweets
133
0 PDF Downloads
0
0 Facebook Shares
Total Usage
133